• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Repair - Simple Fixes You Can Do in a Few Easy Steps

It's easy to assume that a door can't be fixed however, there are many simple fixes which can make a big difference. Let's begin with the shimming.

To shim an opening, open the door and then press it with a firm force into the frame. Use the block or jack plane to remove small pieces of wood from the binding points.

The Frame

The door frame is an important element of your home. It provides security, prevents water damage, and gives your home an attractive appearance. However, it is also susceptible to being damaged. Door frames can be damaged by harsh weather, burglaries, or just regular use. And when they do, it could result in large gaps, poor latching, and a shabby appearance. Fixing your door's frame can be accomplished in a few simple steps.

First, remove the molding or trim the area around your opening. You can use a hammer, the chisel or a power saw to remove the trim. After the trim has been removed, take note of its dimensions so that you can replace it once the repair is complete.

You should then inspect any damaged or rotted areas of the door frame. If you spot any decayed wood, you'll have to replace it. They are typically found at your local hardware store and should be made from an material that is compatible with the rest of your door frame. Avoid pressure-treated wood as it tends to twist and warp with time.

After you have replaced any rotten sections of the frame, you'll have to ensure that it is secured in place. This can be done by using the shim. A Shim is a piece of wood that is placed between the frame and wall. The shim provides extra support for the frame, and will keep it from moving.

After you've replaced any shims, it is a good idea to caulk around the door's frame and sill. This will prevent further water damage as well as protect your door frame from insects.

Finally, you will need to put the trim back on your door frame. If you are lucky, your previous trim may be in good condition, and you can simply nail it back into its place. If not, you might require a new trim and follow the same procedure.

The Threshold

A threshold is a strip of wood used to cover and seal the gap between the door and floor. It also stops water and snow from accumulating within the entrance. A properly installed threshold is not just an essential part of your door, but is also an attractive accent that can enhance the curb appeal of your home. If your threshold is scuffed or damaged, it's time to replace it. Installing a new threshold is not as simple as sliding it into the casing and nailing it into place; it has to be held in place by a series of wood strips, called shims, that are placed between the frame's two jambs.

Cut the old threshold away from the sides with a circular blade (use carbide blades, if you can). If you're able to lift the sub sill, which is the part of the frame that runs underneath the threshold. If it's rotting, replace it at the same time as you replace the threshold.

Use a carpenter's hammer to trace the layout lines prior to cutting the threshold. Take note of the angles that are right for the notches that are able to fit around jambs. Home centers offer thresholds that are cut to match the dimensions of your opening.

Install the shims evenly, and ensure that you space them. If necessary, you can alter the thickness of the shims. However they should not be wider than 1 1/2 inches. It may require a bit of trial and error to make the threshold just right, but still capable of moving freely.

Close the door and see how it opens and shuts. There shouldn't be any light under the door. The sweep at the bottom of the door should be lightly rubbing the top of the threshold.

If the threshold fits well but requires a little more support, apply construction adhesive to the shims prior to pressing them under the threshold. Repeat the process with more shims until you have a tight fit that holds up under weight.

The Hinges

Many door hinges become rusty or degrade over time, making it more difficult to close the door. It is crucial to fix the hinge in order to secure and close the door securely. If you're replacing the hinge be sure to use a similar one that is a good match in terms of size and double glazed windows near me double glazed door repairs windows window doctor near me window repairs near me [get redirected here] edge shape. It is also important to ensure that the hinge is placed in the mortise.

Examine the hinge to determine whether it is loose. If the hinge is not tight it will likely to be snagged along the frame of the door and rub against its strike plate. Look for scratched paint or indents on the frame to indicate the area where the hinge is in contact with. If the issue is that the hinge isn't secure enough, use a screwdriver to tighten it. If the hinge is too loose, you may have to replace it. You can use to put a shim between the door frame and the hinge.

If the issue is that the knuckles on the hinge (the cylinders that the hinge pin fits) are bent and need to be straightened, you'll have to straighten them up to make them point towards the latch jamb. You can bend the knuckles with the help of a large pair of tongue and groove pliers or an adjustable wrench. It's best to only work on one at a time, so you don't accidentally bend out the hinge leaf.

It's also possible that the screws that hold your hinges to the door are loosened. If this is the case, replace the screws with ones that are longer to give them more grip on the hinges.

If the hinge isn't damaged and the screw holes aren't clogged you can use a syringe to inject carpenter's glue into hinge mortise and joint. Then, screw the hinge into the frame, and fix it with a screwdriver or drill. Note the locations of the pilot holes on the door frame and door before installing the new hinges. This will help you to make sure that the screws are placed in the exact same spot as the old ones.

The Hardware

The majority of people don't give much thought to door knobs, locks or levers until they stop working properly. Fortunately, most of these hardware components are repairable. Replacing a door handle or knob is generally a matter of picking out the one that is the most appropriate to the style and design of your home and placing it in place. It's a good idea, especially for exterior doors to install weather-stripping.

If you have a door that is hard to open, you may be able to solve the problem by lubricating the lock assembly. A lot of hinges, handles, and locks can stick when their wear surfaces get dry or dirty. It is inexpensive to keep these components lubricated and double glazed windows near me clean.

The most frequent issues with door hardware are broken or loose handles locks that don't turn on its own when you use hinges and keys that are squeaky or squeak. In most instances you can tighten the screws or replace the screw completely. However, in some cases it's best to remove the lock or handle from the door and sand the spindle, bore of the lock cylinder hole and escutcheon holes ensure they're clean prior to installing the new hardware.

If you have a door that is difficult to close, it could be necessary to grease its locking mechanism with penetrating oil. Clean and reinstall hinge pins using longer screws to fix noisy doors.

If you are replacing a lock, handle or hinge, make sure that the lock you select is compatible with the hole size of your door and jamb. This information is typically found on the packaging or the manufacturer's website. For example, doorknobs or levers require a hole that is specific in its spread (the distance from the center of the hole in the lock to the knob). Examine the backset to determine whether the replacement is compatible with.