• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change of the door lock is an easy and inexpensive method to boost your home's security. The process is not for all. It requires a certain amount of patience and skill.

The cylinder is inside the knob's body. The cylinder is responsible for recognizing the key when it is put into the lock.

Remove the old lock

The first step in replacing the door lock is to get rid of the old one. It is a fairly easy process, but you should keep some things in mind. Make sure that the new lock fits the door. This will ensure that it fits securely, and doesn't create a gap around the deadbolt or latch.

Once you have removed the latch plate look for two screws or bolts on the inside of the casing, which hold the casing and the two halves of the lock together. Remove them with the help of a screwdriver, and then pull the lock out of the door. If you are using a mortise locking system there is a set screw that binds the handle to the spindle. Take off the doorknobs by removing the screw using the help of a screwdriver.

You must also remove the latch and deadbolt plug from the hole in your door jamb. Install your new lock. If you are replacing a mortise lock, you should also measure the distance between the lock case and the edge of your door to ensure that your new lock will fit.

It is possible to replace your lock for various reasons, for instance, if you suspect that someone else holds the key or if you've got new roommates. In any case, you can save money by taking the lock off yourself rather than paying an expert to do it. It is much easier than people think and can be completed in a matter of a few minutes.

Start by getting rid of the handle and trim from the door. Then, pull the trim away with a flat screwdriver. You should be able twist off the majority of it. In some cases you might be able to take off the handles completely. Next, door lock change look for a hole on the inside of the handle and insert straightened clips into it. This will trigger the release mechanism and allow you to remove the handle from the door. Then, look for another small tab on the interior of the lock and press it with a flat screwdriver. Once the spindle is removed, you are able to remove the cylinder and the housing.

The choice of a new locking system

When it comes to choosing a new lock you have a variety of options. Take a look at various types of locks and select one that fits the style of your door. Think about the backset which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, which is a small hole at the edge of your door's frame. Also, ensure that you select a lock that is able to be able to fit the double glazing door lock's thickness and swing.

Most door locks are evaluated by BHMA and the American National Standards Institute to provide you with an idea of how well they stand up to use and how difficult to pick or disable. A lock of grade 3 could be perfect for a quiet apartment in the country, while locks that are grade 1 might be better suited to the busy streets near the storefront.

Most smart door locks require a digital key code to open. If you are worried about hacking, or any other security concerns, speak to a professional locksmith.

Replace the cylinder

You can easily replace damaged or broken doors lock cylinder using a simple DIY project. It is crucial to choose the appropriate cylinder and follow all instructions. First, you must remove the handle or knob if it is present. Then with a screwdriver unscrew the trim that surrounds the lock cylinder. Once the trim is removed, you can reach the screws that keep the cylinder in place and remove them with the flat-head screwdriver. The cylinder is then gently lifted out of the door.

Make sure you measure the length of your new cylinder before installing it. With a tape measure, determine the distance between the cylinder's center and its left and right side. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when doors are kicked or the key becomes stuck inside.

If you have a replacement cylinder, put it into the door and turn the key. This will ensure that the cylinder is in alignment with the carrier, which is normally located on the outside of the lock. Then, loosen the set screws that should be a couple of turns in the head. If there is a screw at the outside of the case that holds the upvc door replacement lock, you'll have to loosen it.

You can replace the lock cylinder you have used with the new one by inserting it into the case, and then tightening the set screws. It is also recommended to reinstall the part that connects the cylinder to the lock indicator stem, which you can do by pulling up three tabs on the back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, Door Lock Change you need to reinstall the strike plate and latch plate, as well as the retaining ring connected to the top of the lock the cylinder.

Installing the new lock

Start by measuring the door's width if are replacing lock in upvc door an existing lock. Most locksets for residential use have a thickness of 1 3/8 to 1 3/4 inches. If your door is thicker, you will need an extra-thick door kit that includes longer screws, a longer tail piece (for door knobs) or spindle extension (for deadbolts).

The majority of locks come with a detailed instruction booklet to assist you in installing the new hardware. Before you begin, go through the instructions to make sure you've followed all the steps. The manual will also provide you with an idea of the degree of skill required to perform the task. It is possible to seek out a friend who has experience changing locks for assistance if are changing locks for the first time.

Before installing the new lock it's recommended to cover the openings with tape the old hardware. This will stop the screws from slipping through the holes, and protect any tiles you may have put in. This will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a piece of painter's tape designed to be used to protect your painter's tape, but you can also use gaffer's tape as well as masking tape in the event that you have it.

After removing the screws that hold the lock's inner half to the exterior then pull the lock straight away. It is important to do this quickly to avoid the lock from closing accidentally and damaging the mechanism.

Install the new latch bolt into the upper cross bore of the new lock if it has one. Make sure to place it in the proper position, which will be indicated by an arrow. Then, slide the latch plate on top of the bolt and secure it in place.

Finally, screw in the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it several times to make sure that it extends all the way to the strike plate and is fully secured. If you're using an electronic smart lock, be sure to follow the instructions for programming it. This involves downloading an app, registering your e-mail address, verifying your identity and connecting to the wireless network to add your device.