• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Saab 9-3 Key

The Saab 9-3 has an impressive variety of appeal to drivers. It is well-lit and has a strong performance engine. It has a high safety rating.

However, it is important to make sure that you have at the very least two keys that work for your vehicle. It can be costly to replace a key if you lose it.

How to replace the ignition Key in a Saab9-3

You need to replace the car key in the event that it isn't turning. This guide will guide you through how to do it on the saab 900 key 9-3. You'll need to replace the key, purchase an updated reprogrammable phone, and then purchase a new casing for your key-fob.

Contrary to earlier models, modern Saab vehicles use an electronic transponder inside the key-fob rather than a physical key that can be used to unlock and start the car. The reprogrammable batteries in the key-fob eventually wear out, and they can't hold any charge. This is particularly the case if you use the same key in the same lock.

A professional locksmith can change the battery fairly easily. You can also do it yourself if have the right tools and a bit of patience. The first step is to remove the key-fob off. Insert flatheads into the slot that is in the middle of your case. The plastic is very thin and it is susceptible to being damaged.

After the case has been opened then you can prepare the new key by combining the lower portion of the key that was used previously with the transponder and banana on the new key. This will ensure that the new key is linked to the CIM properly, which could make a big difference when replacing the original key for your Saab 9-3.

How do I replace the ignition Key on a Saab 900

If you don't have two keys, you will need remove the dashboard and steering wheel in order to access the ignition. Begin by disconnecting the negative battery cable. Once the battery is disconnected, it is possible to remove the trim and saab key Replacement dashboard pieces around the steering wheel. Once the dash has been removed, you can insert a screwdriver into the opening on the back of the ignition switch and remove it.

The ignition barrel has the key lock, which can prevent the vehicle from starting if key isn't in it. If your 900's ignition isn't working, check the key to determine whether it's in the lock or in the ignition barrel. It is also recommended to rotate your keys and keep them clean to avoid breaking.

Saab cars are different from other vehicles in that they don't utilize traditional keys made of metal. The car instead recognizes the electronic signals coming from the key fob through an specialized microchip inside.

If you only lose one key fob that is working, your dealer will charge an extra fee to replace your computer module (also known as the CIM). But we can reprogram your computer's EEPROM, and then prepare it to accept new keys without replacing it. This can save you more than 50% of the cost the dealer charges! We call it the SAAB KEY PROGRAM. Find out more here!

How to Replace the Ignition Key on a Saab 9-5

The metal component of a classic Saab key is easy to copy, and not much of an impediment against theft of vehicles. The electronic component of the key-fob has an electronic chip that detects the car when the key is put in the ignition switch.

Saab's anti-theft system has relied upon this technology for over a decade. It's not quite as effective as a physical door lock however, it makes the theft of your car a lot more difficult. Every Saab owner should keep an extra saab Key replacement key in their car.

The majority of new Saabs are delivered with two keys, but they can be purchased from an dealer by using a handheld device, called a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this is the NG 9-3 vehicles which have more modern, more advanced features that require an ignition key.

The dealer will replace the CIM or TWICE module in those vehicles if all keys are lost, and they'll charge you a premium for doing it. We can reprogram your computer's EEPROM to accept new keys without replacing expensive modules.

How to Replace the Ignition Key on a Saab XC90

If your SAAB 9-3 key fob starts having issues turning the barrel of the lock it could be time to replace it. The process is fairly simple and you don't even need to visit a dealership. You can do it at home, using a couple of basic tools.

First, you'll need prepare the new key. Before you begin, ensure that the anti-theft feature is disabled by placing blocks on your rear wheels and engaging the handbrake. Place the key in the ignition and turn the key to the "on" position. This will activate the accessories but will not start the engine. Repeat this procedure five times and leave the key in the on position.

You'll need to purchase an additional case for your key fob. You can find them at any auto parts shop, and they're typically very affordable. Based on the model, you could even get them without any electronics.

To open the case to open the case, gently push the screwdriver with a flathead into the slot in the middle. After you have split the case, saab key Replacement you will have access to all the internal electronic components. To remove the electronics, make use of a small screwdriver and try to pry them out in a gentle manner.