• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not get rotten or rusty like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, which can make it very dangerous and potentially fatal. It is important to make sure that your windows are in good working order.

For single pane windows, it can be relatively simple to replace them, and the new window will generally fit within the old frame very easily. However If you have double-pane windows that are secured by internal beading, it'll be more difficult to get rid of the panes that are in place and replace them with new ones. In this case you'll need source some plastic spacers to assist the new pane to fit perfectly into the frame of the window.

If you plan to attempt to remove the window panes yourself it is important to wear appropriate safety gear, including thick gloves and eye protection. It is also recommended to lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall on the fabric and not on the floor which could cause them to be trampled under.

Once the glass is removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to block water and drafts from entering the home until a professional comes out and fix the window. This will also act as a barrier that will prevent any intruders to gain access to your home. If the gap between the window and window repair the door is significant, you may want to use security screens that has an opening. This will provide the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. However, over time they can suffer from a variety of problems including sliding. A sagging window can cause problems with light, draughts or even security. It's crucial to act immediately if you discover that your uPVC windows are sliding.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to unblock the windows to reach the frame. With the screwdriver, you'll be able to take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've adjusted the hinges, shut your window repairs and verify the fitting. If you're satisfied with the fit, you can tighten the screws until they remain in the right place.

If you aren't able to move the hinges you may require replacing the seal. Rubber seals can dry out and lose their elasticity over time, leading them to loosen. If this happens, it's crucial to replace the seal as fast as you can to ensure that your uPVC windows are watertight and draught-proof.

uPVC handles may also loosen. This is typically caused by screws that have been removed over time, but it could also be due to the handle mechanism wears out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to shut the window and perform an experiment fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it does not, you can use the screwdriver to loosen the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you're waking up to damp floors and window repair mouldy walls every time it rains it is important that you take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature inside your home. The most common reason for leaks in uPVC windows is that the sealant around the frame is either damaged or not present.

It is a fairly easy fix and should be undertaken by any competent DIYer. Depending on the severity of the issue is, old caulking may have to be removed. When it comes to uPVC repair, it is important to avoid 'over-caulking'. This will make your window more difficult to clean and reduce its energy efficiency.

Verify that the drainage holes do not have debris in them and ensure that the sill pan has been properly angled to drain away from the window. In more serious instances, you may need to think about replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage is occurring between the double-glazed glass, it is more likely that the issue is more related to the seal, not the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and open in a breeze it could be hinges at the fault. Any competent DIYer can replace the hinges in a matter of minutes.

Like all mechanical parts hinges will be damaged over time. It is essentially a very simple procedure, but it is easier to do with someone else to help hold the frame up.

Make sure that the uPVC hinges open and close in the correct direction. This can be done by checking for the arrows on each hinge. This shows which way the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window a certain way or due to improper installation in the factory. Sending us a photo via our website is often enough to resolve the problem. We are more than happy to give assistance.

It is also important to lubricate the hinges regularly. Applying an engineering lubricant that is light to the hinges is a good method of doing this. We recommend using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. This must be done at a minimum once a year. WD40 or other solvent-based lubricants should not be used as they could damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different factors. The hinges may also become unbalanced due to wear, which can cause a gap where the sash and frame meet. They can be repaired by giving them good cleaning, but when they're beyond repair, it may be necessary to get them aligned or replaced. The interlock, which is located on the hinge side of the Window repair, can also become misaligned, again it is possible to just give them a clean but in certain cases, it may be necessary to have these replaced.

The next most common reason for draughts is window seals. They can become worn down or damaged over time and allow air to escape through the gaps. Replacement of these with high-quality weatherstripping can help keep draughts at bay. Replace the upvc windows with low-emissivity glasses. This will help regulate indoor temperatures and decrease the risk of draughts.

Lastly, one of the most effective methods to reduce the draughts in your home is to use a draught excluder, these are typically fabric tubes that are filled with some sort of filler and can be positioned on top of your windowsill. They will help keep cold air out and keep your home warm and cozy!

Your windows made of upvc will continue to provide excellent insulation and security for your home by performing regular maintenance and repairs. It is essential to remember that all windows eventually become worn out, and it could be more cost-effective to simply replace them than to repair them. If you have any problems with your upvc window you should consult a professional as soon as you can.